LE WILSON Case Gage - British Calibers

Brand: LE Wilson
Model Code: CG-17HH
Availability: 10

0 Review(s) Add your review

Caliber

Quantity

40.00$

Tags: cg-17hh, le wilson, caliber, 17 hornady horner, 17 remington, cg-17rem, 17 remington fireball, cg-17fb, 204 ruger, cg-204r, 218 bee, cg-218b, 219 donaldson, cg-219d, 219 zipper, cg-219z, 22 br, cg-22br, 22 hornet, cg-22h0r, 22 nosler, cg-22n0s, 22 ppc, cg-22ppc, 22 remington jet, cg-22rjt, 22 creedmoor, cg-22cre, 22 - 250, cg-2250, 220 swift, cg-220sw, 221 remington fireball, cg-22rfb, 222 remington, cg-222r, 222 remington magnum, cg-22rmg, 223 remington, cg-223r, 224 valkyrie, cg-224v, 225 winchester, cg-225w, 243 winchester, cg-243w, 25 - 06, cg-2506, 25 wssm, cg-wssm30, 250 savage, cg-250s, 256 winchester magnum, cg-256wm, 257 roberts, cg-257r, 26 / 28 nosler, cg-n0s, 260 remington, cg-260r, 270 winchester, cg-270w, 270 wsm, cg-27sm, 280 remington, cg-280r, 280 ackley improved, cg-28ack, 300 ultra, cg-ulmg, 30 - 06, cg-3006, 30 - 30, cg-3030, 30 - 40, cg-3040, 30 br, cg-30br, 30 nosler, cg-30n0s, 300 rsaum, cg-rsaum, 300 aac blackout, cg-3acc, 300 norma magnum, cg-300nm, 300 prc, cg-3prc, 300 savage, cg-3sav, 300 wsm, cg-30sm, 303 british, cg-303b, 303 savage, cg-303s, 308 winchester, cg-308w, 325 wsm, cg-325sm, 33 xc, cg-33xc, 33 nosler, cg-33n0s, 338 edge, cg-338ed, 338 federal, cg-338f, 338 lapua, cg-338l, 338 norma magnum, cg-338nm, 348 winchester, cg-348w, 35 remington, cg-35r, 35 whelen, cg-35wln, 357 sig, cg-357s, 358 winchester, cg-358w, reloading dies, 220 wilson arrow, cg-22wa, 223 / 243 wssm, cg-wssm28, 25 - 20, cg-2520, 25 - 35, cg-2535, 25 - 45 sharps, cg-2545s, 32 - 20, cg-3220, 32 winchester special, cg-32ws, 375 ruger, cg-375r, 38 - 40, cg-3840, 44 - 40, cg-4440

Description
Reviews

One piece gage that will check overall length to indicate the need for trimming, datum to head length to assure correct headspace and to prevent over sizing. Available for most popular rimless cases. The Cartridge Case Gage was designed with safety in mind and was invented by our founder Sam (L.E.) Wilson in 1935 after a fellow shooter approached him for help in solving a case-separation issue. The gage allows you to see just how much you are sizing back your shoulder on your cases.

This is best done by following the steps below.

Measure a case in AS-FIRED condition. Note headspace measurement
Resize case on current die setting
Then place back in the gage to see just how much you are sizing the shoulder back. This can be measured by using the Case Gage Depth Micrometer
Finally, adjust sizing die accordingly to desired shoulder set back.

After sizing your cases, there is a good chance the brass will lengthen. The gage will also check min/max case length and will point out the need for case trimming. This is an essential tool for every reloader.

Note: Does not measure body diameters. This gage is intended to be used with fired cases to determine a basis for full length sizing and trimming.

Overall Rating 0

Write a review

Your Name

Your Review

Note: HTML is not translated!

Rating Bad Good

Captcha

Enter the code in the box below